Our windows are tested with a maximum pump down rate of 0.33 atm/sec and a maximum vent rate of 0.40 atm/sec For reference visit: Here

Our standard beryllium sizes can be found in our design guide for beryllium windows:
Design guidelines for DuraBeryllium Windows

We also offer standard beryllium windows in conflat flanges:
Standard Conflat Flange Window Options
Contact an Expert

Our standard sizes are 10mm², 20mm², 30mm², 50mm², 80mm², 100mm² and 140mm². We can also talk to you about custom sizes and geometry.

AP Window Technical Note
Consult a Moxtek expert >

In most cases, you would use our DuraBeryllium windows to detect elements as light as sodium and our AP windows for elements as light as beryllium (Be).

Visit our AP window page >
Visit our DuraBeryllium window page >

DuraCoat is our patented corrosion prevention coating that increases the life of your window, especially if it’s exposed to humidity or other corrosive environments. For minimal transmission loss, we make DuraCoat with elements lighter than oxygen.

Visit our DuraBeryllium product page >

DuraCoat Plus is a polymer film added on top of our standard DuraCoat that adds additional corrosion prevention and leak integrity.

Yes

Generally, you would apply DuraCoat to any exposed surface using a proprietary deposition process.

Yes you can.

On each of our X-ray windows product pages, we've included a downloadable datasheet with that information.

On each of our X-ray windows product pages, we've included a downloadable datasheet with that information.

Please see our window mount design notes.

Ultra-thin AP Window Mount
Design Guidelines for DuraBeryllium window mount

Under normal conditions and intended use, our X-ray windows have no exposure limits, nor do they represent an inhalation, ingestion or contact hazard.

Please reference our Material Safety Datasheet (MSDS) for conditions that could cause harmful exposure to beryllium.

See Material Safety Datasheet >

We are capable of providing bare beryllium. However, for your window’s protection, we strongly recommend using DuraCoat.

At this time, we only sell PIN detectors.

Yes. We also offer tubes with voltages ranging between 50kV and 70kV. Please visit our X-ray sources page for more information on specific models.

Yes, our MAGPRO™ 70kV source can be used for imaging. Please visit the product page for more information.

Each X-ray source web page contains a downloadable datasheet with that information.

Visit our X-ray Sources page >

For XRF, tungsten is often used for metal identification RoHs/WHEE. Likewise, Rhodium or silver is typically used for light element analysis, detection of aluminum, magnesium, sulfur, etc.

Consult a Moxtek expert >

Moxtek source spot sizes now range between 50 microns and 800 microns.

Consult a Moxtek expert >

For monoblocks:
We have a 4W (max), 50kV (max) monoblock source that is as small as 6” (150mm) long by 1” (25.4mm) wide by 2” (51mm) tall.
We have a 12W (max), 60kV (max) monoblock source that is as large as 6.5” (165mm) long by 1.35” (35mm) wide by 2.75” (70mm) tall.

For cabled power supplies, the power supply boxes range as follows: We have a 4W (max), 40kV (max) power supply that is as small as 5” (128mm) long by 0.8” (21mm) wide by 2” (51mm) tall, cables running between 4” (102mm) and 11.5” (292mm).
We have a 10W (max), 50kV (max) power supply that is as small as 5.7” (145mm) long by 0.9” (23mm) wide by 2.25” (57mm) tall, cables running between 4” (102mm) and 11.5” (292mm).

The tube shields range greatly, typically between 1.125” (29mm) and 1.25” (32mm) in diameter, 2.18” (55mm) to 2.5” (64mm) long.

Specific source dimensions are also on their respective Datasheets

Yes, Moxtek offers power supplies with our X-ray tubes.

We recommend our FTC-200 X-ray Tube Controller. For more information, we’ve posted a lot about this product on its detailed web page.

Visit our FTC-200 Tube Controller page >

The Optional Ribbon Cable is included with each of our FTC tube controllers. Our 2-PIN Secondary Cable is included with our standard 50kV cabled units. At the customer’s request, we will deliver the Optional Ribbon Cable and or Optional 2-pin Secondary Cable separately.

At 40kV, our tungsten sources give off approximately 3.0x10¹¹ photons/second/steradian/100uA. Our silver sources (also at 40kV) give off approximately 1.5x10¹¹ photons/second/steradian/100uA.
Consult a Moxtek Expert

Each product web page contains detailed warranty information.

Visit X-ray products warranty >
Visit Optics products warranty >

Yes. We specialize in encapsulation services, please contact us for more details.

On the right-hand side of each product web page is a "Request a Quote" button. Clicking it presents a form with the required details (e.g. contact information, etc.) we need to create a quote. In the comments field of that form, you can include a brief description and the required dates and specifications of your request. Once we receive your information, we’ll respond promptly.

Consult a Moxtek expert >

Yes. That’s a core element to our service. We excel at meeting customer-specific requirements.

The lead time is typically 2-6 weeks. Custom order lead time is determined on an individual basis.

Yes, we do.

View our Distributors page >

You can request a quote from any one of our product pages.

Consult a Moxtek expert >

Lead times vary depending on the samples you’re interested in. You can request a quote from any one of our product pages.

Consult a Moxtek Expert >

Lead times vary depending on the pieces you’re interested in. You can request a quote from any one of our product pages.

Consult a Moxtek Expert >

Never do we knowingly purchase conflict minerals. We purchase the following minerals from conflict free smelters: tin, tantalum, tungsten, and gold. We require our suppliers to purchase these metals from conflict free smelters, as well.